الدفع نوع: | L/C |
---|
فترة الضمان: 3 سنوات
دعم التخصيص: OEM, التصميم
محيط: تويست مثقاب
تطبيق: حفر المعادن
المعالجة السطحية: آخر
إنتاجية: 100, 000PCS Per Month
نقل: Ocean,Land,Air,Express
الدعم: 100, 000PCS Per Month
الشهادات: RoHS, CE, UL, BS, CCC, GS, Many
الدفع نوع: L/C
Processing impact editing
(1) The diameter of twist drill is limited by the aperture, the spiral groove makes the drill core thinner, the drill bit stiffness is low; With only two ribbed guides, the axis of the hole is easy to skew; The horizontal edge makes centering difficult, axial resistance increases, and the bit is easy to swing. Therefore, the shape and position error of the drilled hole is large.
(2) Twist drill before and after the tool surface are curved, along the main cutting edge of each point of the front Angle, the rear Angle is not the same, the front Angle of the horizontal edge of -55°. Poor cutting conditions; The distribution of cutting speed along the cutting edge is not reasonable, and the cutting speed of the tip with the lowest strength is the highest, so the wear is serious. Therefore, the hole precision of processing is low.
(3) The whole edge of the main cutting edge of the drill participates in cutting, and the cutting speed of each point on the edge is not equal, which is easy to form spiral chips and difficult to discharge chips. Therefore, the chip and the hole wall extrusion friction, often scratch the hole wall, the surface roughness after processing is very low.
نموذج رقم. GMSD367
Material |
Component (%) |
HSS 4241 |
C (0.9~1.0); Si(1.0~1.3); Mn(0.25~0.4); P(0~0.035); S(0~0.009); Cr(3.8~4.2); Mo(0.55~0.85); W(1.6~2.0); V (0.4~0.65); Co(0) |
HSS 4341 |
C (0.83~0.93); Si(0.2~0.4); Mn(0.2~0.4); P(0~0.03); S(0~0.009); Cr(3.8~4.4); Mo(2.5~3.5); W(3.5~4.5); V (1.2~1.8); Co(0) |
HSS 6542 (M2) |
C (0.8~0.9); Si(0.2~0.45); Mn(0.15~0.4); P(0~0.03); S(0~0.009); Cr(3.8~4.4); Mo(4.6~4.9); W(5.6~5.9); V(1.8~2.0); Co(0) |
HSS 9341 |
C (0.77~0.87); Si(0.2~0.4); Mn(0.2~0.4); P(0~0.03); S(0~0.009); Cr(3.8~4.4); Mo(2.7~3.3); W(8.5~9.5); V(1.3~1.7); Co(0) |
HSS M35 (Co5%) |
C (0.8~0.9); Si(0.2~0.45); Mn(0.15~0.4); P(0~0.03); S(0~0.009); Cr(3.8~4.4); Mo(4.6~4.9); W(5.6~5.9);V(1.8~2.0); Co(4.6~4.9 |
سؤال وجواب:
1. هل أنت مصنع؟ هل لديك مصنع؟
نحن الشركة المصنعة المحترفة ، لدينا أكثر من 5 سنوات خبرة في هذا المجال.
2. هل الشحن المجاني ممكن؟
نحن لا نقدم خدمة شحن مجانية ، لكننا سنقدم لك بعض الخصم إذا اشتريت منتجات كمية كبيرة.
3. هل يمكنك إرسال منتجات إلى معاييرنا في الصين؟
نعم ، إذا كان لديك تكليف في الصين ، فسوف يسعدني إرسال منتجات إليه.
4. هل تصنع OEM؟
نعم فعلنا. لدينا آلة ليزر ، ويمكن أن تنص على شعارك وأحجامك على جسم قاطع الطحن ، ويمكن أيضا طباعة الملصقات.
5. كيف وقت التسليم؟
وفقا للأحجام والكمية ، وقت التسليم مختلف. عادة ما يكون 5 ~ 10 أيام. يمكننا أن نخبرك بحالة المخزون الدقيقة إذا كنت بحاجة.
6. هل يمكنك إنتاج أداة خاصة كربيد؟
نعم نستطيع. من عام 2013. سوق مصنعنا الرئيسي هو من طواحين نهاية قياسية إلى أدوات خاصة. أداة خاصة وفقًا للرسم والعينة.
اشترك في النشرة الإلكترونية:
الحصول على التحديثات، خصومات وعروض خاصة وجوائز كبيرة!